Sprinkler Repair in Delray Beach: Common Problems and Fixes

Most sprinkler problems in Delray Beach come down to a few causes: a broken or clogged head, a leak in the line, a valve or wiring fault that stops a zone, or a timer and rain sensor that are set wrong or not working. Start with the timer and a quick walk of each zone. Small fixes like a cracked head or a clogged nozzle are often simple. If a zone won't turn on or shut off, or you find a leak underground, it's time for a professional repair.
Start with a zone-by-zone check
Run each zone one at a time from the controller and walk it while it runs. Look for:
Heads that don't pop up, spray sideways, or mist instead of spraying
Water bubbling up from the ground or pooling in one spot
Dry areas the spray doesn't reach
Water hitting the driveway, street or house walls
Write down which zone and which head has the problem. That list makes any repair faster, whether you fix it yourself or call us.
Problem 1: A zone won't turn on
When one zone stays off but the others run, the cause is usually at that zone's valve: a failed solenoid, a loose or cut wire, or debris inside the valve. If no zones run, check the controller first. Is it powered? Is the date and time correct? Are watering days actually selected? Is the rain sensor holding the system off after a storm? Florida law requires automatic sprinkler systems to have a working device that stops watering when there's enough moisture. So a rain sensor doing its job after a wet week is normal.
Problem 2: A zone won't shut off
A zone that keeps running after the controller turns it off usually has a valve that's stuck open, often because of debris or a worn diaphragm. Turn off the water to the irrigation system to stop the flow, then get the valve looked at soon. A running zone wastes water and can soak your lawn and beds.
Problem 3: Broken, clogged or misaligned heads
Mowers, foot traffic and cars backing up are hard on spray heads and rotors. Common signs:
Geyser or flooding at one spot: a broken head or nozzle
Weak or uneven spray: a clogged nozzle or filter screen
Spray hitting pavement: the head has turned or the arc needs adjusting
Swap like for like. Mixing head types in one zone causes problems because rotors, fixed spray nozzles and rotary nozzles each put down water at very different rates (UF/IFAS). A mixed zone ends up with soggy spots right next to dry ones.
Problem 4: Low pressure across a zone
If every head in a zone runs weak, check for a leak first: wet soil, a sunken spot or water seeping up between heads. A partly closed valve or too many heads on one zone can also lower pressure. When low pressure shows up suddenly, it usually means something broke. When it builds slowly over time, it often points to clogging or a system that has grown past its design.
Problem 5: Brown or soggy patches
Brown spots in a lawn that is otherwise watered usually mean a coverage gap from a blocked, tilted or broken head. Soggy areas usually mean a leak or a zone that runs too long. UF/IFAS notes that on Florida's sandy soils, long run times can push water below the roots. Set each zone based on its sprinkler type and the season rather than one fixed schedule for every zone. Before you change the run time, fix the head or leak causing the problem.
Problem 6: The timer is set wrong
A lot of "broken system" calls turn out to be programming problems: a reset clock after a power outage, an old seasonal schedule, or watering days that don't match the local rules. UF/IFAS recommends using the controller's seasonal percentage adjustment to cut run times when the grass isn't actively growing in winter, and raising them again in the warm months.
Watering rules to keep in mind in Palm Beach County
The South Florida Water Management District's year-round rule (Chapter 40E-24, F.A.C.) bans landscape watering between 10 a.m. and 4 p.m. and limits it to two or three days a week, depending on the area. Watering days depend on whether your address is odd or even. Cities can adopt their own schedules, so check your local ordinance for exact days. The rule makes exceptions for irrigation system maintenance and repair, new landscaping and low-volume watering. Running zones to test a repair is allowed.
Palm Beach County Water Utilities also recommends watering only when needed, early in the morning or in the evening, and making sure every sprinkler system can shut off for rain.
When to call a professional
Call for repair when:
A zone won't turn on or won't shut off
You see signs of an underground leak or a sudden pressure drop
Wiring, valves or the controller need replacing
The same problems keep coming back
Under Florida law, a licensed contractor who works on an automatic sprinkler system must test the rain shut-off device and repair or install one if it isn't working before finishing the other work.
Need help? Delray Garden Center handles sprinkler and irrigation repair in Delray Beach and nearby Palm Beach County communities. Stop by 3827 W Atlantic Ave, Delray Beach, FL, or request an estimate.
FAQ
Why won't one of my sprinkler zones turn on?
It's usually that zone's valve: a failed solenoid, a damaged wire or debris. If no zones run, check the controller's power, clock, watering days and rain sensor first.
Why does my sprinkler keep running after it's supposed to stop?
A valve stuck open, often from debris or a worn part. Shut off the irrigation water supply and have the valve repaired.
Can I run my sprinklers outside my watering days to test a repair?
Yes. SFWMD's year-round rule includes an exception for irrigation system maintenance and repair. Check your city's ordinance for the exact conditions.
Do I need a rain sensor in Florida?
Yes. Florida Statute 373.62 requires automatic sprinkler systems to have working technology that stops watering when there's enough moisture.
How long should each zone run?
It depends on the zone's sprinkler type and the season. UF/IFAS notes that long run times on Florida's sandy soils can push water past the roots, and recommends cutting run times back in winter when grass is less active.
_edited.png)

Comments